Ready Access AA300 Especificações

Drive-Thru Window 600 Series Security Windows Model 600 Model 602 / 604 Model 601 / 603

9 SPECIFICATIONS AND PERFORMANCE MODEL 600 Unit Voltage Model Number USA International Actual Unit Amps Dimensions In Inches W X H x D Weight I

10 Dimensions Model 600 MODEL 6004.50" [114mm]34.75" SO [883mm]43.50" [1105mm]47.50" [1207mm] Dimensions In Inches W x H x D

11 MODEL 601 / 603 MODEL 601MODEL 60317.00" [432mm]58.50" [1486mm]58.50"[1486mm]47.56"[1208mm]17.00"[432mm]15.00"[381mm

12 MODEL 602 / 604 MODEL 604MODEL 60247.50"[1207mm]60.50"[1537mm]47.50" [1206mm]60.50" [1537mm]34.75" SO [883mm]17.00" [

13 Safety Information WARNING: To avoid the risk of fire, Electric Shock or injury to persons, observe the following: 1. Before servicing or cleani

14 Physical Installation Model 600 Before you begin installing your Ready Access Drive-Thru Window, you must determine what type of installation will

15 MODEL 601 / 603 Before you begin installing your Ready Access Drive-Thru Window, you must determine what type of installation will be required. Exa

16 MODEL 602 / 604 Before you begin installing your Ready Access Drive-Thru Window, you must determine what type of installation will be required. Exa

17 WARNING: TWO PEOPLE ARE REQUIRED FOR THE LIFTING AND INSTALLATION OF THE WINDOW. 1. Confirm that the customer-supplied frame is made to accommoda

18 7. Using the window mounting holes as a template, drill a quantity of 4 – 3/16” (5mm) diameter holes for mounting. (See Figure 5) Figure 5 8

1 TABLE OF CONTENT Topic Page Disclaimer 2 Serial Number Identification 2 Contact Sheet 2 Introduction 3 Product Informat

19 Electrical Installation – 10/2003 Chassis Style All power must be connected and wired by a qualified electrician and must be in compliance with al

20 2. Wire the AC source line to the Terminal Block located in the header of the window. NOTE: THE GROUND WIRE (GREEN) IS ALWAYS IN THE CENT

21 Initial Window Operation Testing Procedures Action Reaction Turn the power “OFF” at the rocker switch located on the controller unit. Manually

22 Adjustments and Calibrations SuperScan Presence Sensor Adjustment Instruction Once the window is installed and the power is hooked up to the driv

23

24 Door Alignment Adjustments to the door height and alignment are accomplished by turning one or both of the eccentric nuts located at the top of th

25 Calibration: The only calibration available on the new style DC-3 PC board is setting the close delay timer using the dip switch package mounted n

26 Operation Procedures Modes of Operation: The Model 600 Single Door Slider window has two modes of operation, Manual and Automatic. After install

27 Controls Identification, Explanation and Function Controller Unit Lamps and Switches Function Power Lamp This lamp indicates that the power r

28 Maintenance Maintenance Schedule Scheduled maintenance should be performed on a regular basis. This is to assure proper operation and performanc

2 DISCLAIMER READY ACCESS DISCLAIMS ANY LIABILITY FOR ANY DAMAGE OR HARM CAUSED TO THE MODEL 600 DRIVE-THRU WINDOW, IT’S OPERATOR OR ANY OTHER EQUIPM

29 SERVICE Troubleshooting Guide Issue Probable Cause Resolution • No power to the controller unit Ø Main Circuit breaker is defective or not “O

30 Issue Probable Cause Resolution • Defective motor assembly Ø To test for a defective motor, open and close the door with the power “OFF”. If t

31 Issue Probable Cause Resolution • Loose or broken connection to the PCB Assembly • Secure the cable connector to the PCB assembly or replace t

32 Parts Lists Parts List (Description/Part Number) Description Current Part Number Previous Part Number Note Cable & Chain Assy ( New Chassis )

33 Drawings Exploded Views Page Part Number If Applicable Description 28 N/A Header Assembly – Exploded View 29 85186700 Motor and Clutch Assem

34 REF ID # PART NUMBER DESCRIPTION REF ID # PART NUMBER DESCRIPTION 1 85002910 Solenoid and Hook Assy R/L 5 20220003 AC Terminal Block

35

36 85003600 Roller Grove Bearing 20220001 Mounting Block 85003200 Roller Block Assembly 85004500 Thumb Turn Lock Latch 85004400 Self-Closi

37 20090087 Face Plate 20090086 Dead Bolt Lock 20090084 Mortise Thumb Turn 20110022 Power Supply 20110021 Speaker 20110020 Phone Intercom

38

3 INTRODUCTION The Ready Access window is quality designed to give you years of reliable, trouble-free service. Each window is shipped pre-assembled,

39 REF ID # PART NUMBER DESCRIPTION 1 Call for Part # Drawer 2 40010030 Bumper 3 Call for Part # Adjustment Screw 4 Call for Part #

40 REF ID # PART NUMBER DESCRIPTION REF ID # PART NUMBER DESCRIPTION 1 See Parts List Door Assembly 8 85004500 Latch Lock Thumb Turn 2 8

41

42 Appendix A Adjusting or Re-hanging the Door The distance of the door(s) above the mullion or counter top is adjusted by turning the eccentric nut

Ready Access, 1815 Arthur Drive, West Chicago, Illinois 60185, Tel: 630-876-7766, Tel: 800-621-5045 Fax: 630-876-7767, Email: [email protected],

4 PRODUCT INFORMATION Model 600 • The Model 600 has a moveable Service Panel. This offers the option of servicing customers personally. The service

5 Model 601 / 603 • The Model 601 has a moveable Service Panel. This offers the option of servicing customers personally. The service panel self latc

6 • Fully Assembled, Ready to Install Ready Access windows are shipped completely pre-assembled, and fully glazed for lower installation costs. Norm

7 Model 602 / 604 • The Model 602 has a moveable Service Panel. This offers the option of servicing customers personally. The service panel self latc

8 • Fully Assembled, Ready to Install Ready Access windows are shipped completely pre-assembled, and fully glazed for lower installation costs. Norm